1000RPM Gear Motor 3-6V DC Geared Motor Axis
January 2, 2024
100K ohm resistor
January 2, 2024
Soldering Paste
RM5.50
100g Soldering Paste Repair Solder Tin Cream Welding Fluxs Seal Grease Tools
Description:
It is applicable for mobile phones, PC cards,BGA and other sophisticated electronic chip-level flux welding.Easy to use, no residue and clean.
Features:
Advantage: Non-toxic, non-corrosive, good insulation, smooth welding surface, no deterioration no dry.
Function: It cleans and prevents metal oxidation, so it is effective to allows solder to create strong, long lasting mechanical and electrical bonds.
Easy to use: Easy to use, no residue and clean.
No Corrosion: There is no corrosion to IC and PCB.
Boiling point: It is only slightly higher than the melting point of the solder
Safe to use: Environmental and nontoxic, odorless and stable for use.
Application: It is applicable for mobile phones, PC cards, BGA and other sophisticated electronic chip-level flux welding.
Specification:
Material: Rosin
Type: Paste
Weight: 100g
Size: 6.5 x 2.5cm
Method of use :
1. Use the end of a match or toothpick, apply a little soldering paste to the leads which need to be soldered.
2. Place the soldering iron tip over the leads. Making the solder against these leads. Heat the solder till it flows freely, then move the soldering iron and solder away in a rapid speed.
Related products
-
Atmel ATmega328P-PU
RM25.00DescriptionAtmel’s ATMega328P 8-Bit Processor in 28 pin DIP package. It comes with 32K of program space. 23 I/O lines, 6 of which are channels for the 10-bit ADC. Runs up to 20MHz with external crystal. Package can be programmed in circuit. 1.8V to 5V operating voltage! The famous Arduino Deumilanove, and Arduino UNO is using this ATMega microcontroller. Anyhow, this microcontroller is fresh new without any bootloader.
Good news! Start from August 2012, this microcontroller is pre-loaded with Optiboot bootloader (Uno 16MHz). This means you can use Arduino code in your own project without using an actual Arduino Board. No programmer is needed anymore but you still need UC00A and basic circuit. Please select Arduino Uno Board in the Arduino IDE. We are using this microcontroller in our Breadboard Friendly Arduino (BBFuino). Therefore, you can refer to BBFuino’s schematic and tutorial for more information.
-
Sg90 Tower Pro Mini Servo Motor Compatible with Arduino
RM9.00DescriptionNote: If you are using a microcontroller based on Raspberry Pi, micro:bit, REKA:BIT (ZOOM:BIT), and ESP WiFi series, we recommend using TS90A micro servo which supports 3.3 DC Voltage.
This is a low-cost plastic gear RC servo with 1.80kg.cm holding torque (at 4.8V). It is a perfect solution for student robotic projects who build arms or linkages. The advantage of the RC servo over the DC brush motor is the ability to control its rotation angle.If you are building a system or project that uses many RC servo motors, please consider getting the 8 Channels Servo Controller. They will make your life easier. -
5VDC 10A Single Channel Relay Module compatible with arduino
RM5.00DescriptionNote: From February 2020 onwards, the module comes with a logic low circuit.
The Relay breakout board is a convenient board to be used with 5V microcontrollers such as SK40C, SK28A, Arduino, SKds40A, SK18B. You can easily use 5V signal to control the relay. Three inputs:
- VCC = 5V is needed
- GND = Common Ground, 0V
- IN = Control signal need to be
5V0V to activate the Relay (Active Low)
The relay terminals (COM, NO, and NC) are brought out using a 3-way screw terminal. On-board relay is rated at 10A. It can be used in many applications: controlling high voltage, high current loads such as motor, solenoid valves, lamps, and AC load. It also comes with 2 LEDs to indicate the status power (VCC) and the status of the relay.
Note: This is an
active-highactive-low device, which means logichigh (5V)low (0V) at pin IN will trigger the relay.
Reviews
There are no reviews yet.